Dallas, Fort Worth, Houston, Austin,South Dallas, North Dallas, Dallas County, Houston, Corpus Christi, San Antonio, DFW metroplex, Dallas - Fort Worth, Abilene, Amarillo, Odessa, Midland, El Paso
Fire Retardant Coatings - Flame Retardant Coatings - Fire Retardant Sprays
INTERIOR FIRE RETARDANT
COATING or SPRAY FOR ALL WOOD PRODUCTS
PLYWOOD ● LUMBER ● TIMBER ● OSB●I-JOISTS
FIRE RETARDANT COATING
SURFACE BURNING CHARACTERISTICS OF APPLIED COATING
Surface
Douglas fir
Flame spread
35
Smoke developed
95
Number of preliminary coats
None
Rate per coat (ft2/gal)
--
Number of fire retardant coats
3
Rate per coat (ft2/gal)
330 to 450
Number of overcoats
None
Rate per coat (ft2/gal)
--
Flash point of liquid coating:
Fire retarding coating - closed cup,
no flash
TECHNICAL DATA
INTERIOR CLASS B RATING
ASTM E84 Class B Coating Flame Spread 35 to 75
PRODUCT DESCRIPTION:Aqueous Based Resin
PRODUCT ANALYSIS
Total Solids
27 to 31.5%
PH
2.5 - 3.0
Weight per gallon
9.4 - 9.8 lbs
Flash point
Non-Flammable
Specific gravity
1.104
Color
Water clear at 78°F. - Slight haze at 50°F. or lower
Volatability
Non-Volatile
Solvents
Water(Contains no petroleum or derivatives of petroleum)
Anti-Fungus
Mildly Resistance
Bacterial
Mildly Resistance
Linear shrinkage
None
Moisture Absorption
None
Corrosive
Mildly
Toxic
None (when dry)
Insects, rodents,
aspergilli And other
types of molds
Mildly resistance
Termites
Mildly resistance
Preservative for wood
None
RECOMMENDED USE: Interior Class B Rating (Flame spread 35)
FLAME SAFE WOOD SAFE is a fire retardant coating. It can
be used on any type of wood or porous materials, such as:
Yellow Pine
Cedar
Spruce-Pine-Fir (SPF)
Douglas Fir
Straw
Cellulose Materials
Redwood
Blown Insulation
Wall Coverings
Paneling
Acoustical ceiling tiles
Cellotex-soundproofing
ENVIRONMENTAL REGULATION:This product complies will U. S. Federal Regulations concerning the use of lead in paint
and hydrocarbon emissions.
QUICK REFERENCE FOR APPLYING WOOD SAFE FIRE RETARDANT COATING
MATERIAL
APPLICATION
COVERAGE
Interior wood
Any type of soft woods such as:
Yellow Pine, Douglas Fir, SPF, Redwood, plywood and textured plywood
Treat before, during or after construction.
Be sure surface is clean and dry before treating.
Apply with sprayer head held at 8 to 12 inches from surface
Apply with brush or roller.
May be necessary to wipe on hardwood surfaces
Treat all surface areas where possible
Do not expose treated area to moisture for 24 hours.
Apply three (3) coats at 330 - 450 sq. ft. per gallon with the final coverage rate of 110 sq. ft. per gallon
INTERIOR:
All surfaces to be treated must be clean
and dry. Wood Safe fire retardant coating is water-based, clear liquid that
becomes insoluble when dry.
Wood Safe
also inhibits mold and mildew protector and repels insects. If over coating is intended, Wood Safe is an excellent primer for use under
latex paints and allows a surface to be tinted witht water based stains.
DO NOT DILUTE OR MIX WOOD SAFE fire retardant coating WITH ANY OTHER PRODUCTS.
Avoid wasteful runs and dripping. It should be noted that unlike some
products, materials treated with Wood Safe
fire retardant coating requires no special cutting tools or special
fasteners. Contact parts of any equipment
should be stainless steel or plastic to prevent
chemical reaction and breakdown. Storage
may be done in polyethylene containers.
Wood Safe fire retardant coating provides a structure long term fire retardant protection.
CAUTION:
Product must not freeze. It must not be thinned or diluted.
OVERSPRAY:
The overspray will not harm plants or animals. Spills can be flushed with water.
A rag wetted with bleach and water mix will clean up spotting.
CLEAN UP PROCEDURE:
Airless Equipment.
1. Run clear water through the system until coating is flushed out. When minor
sudsing on surface stops, the system is flushed.
2. Run bleach and water mix (1 part to 4 parts) through system as solvent for
cleaning any residue.
3. Repeat Step 1 if any foaming occurs in Step 2.
4. Lubricate system as specified by equipment manufacturer to combat rusting.
If two or more applications are planned in the same day, the sprayer can be kept
clean by running water through the system between applications.
Brushes/Rollers.
1. Clean immediately after use.
2. Wash thoroughly with bleach and water mix (1 part to 4 parts).
SAFETY FIRST
Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When
working on steep or high areas. Take EXTREME CARE not to step on wet
treated area. Surface may be slick until dry.
It is good practice to wear respirator or mask and protect hands with rubber
gloves when spraying any coating or chemical. When engineered air control is
not feasible, use properly maintained and properly fitted NIOSH approved
respirator for solvent vapors. A dusk mask does not provide protection against
vapors.
If eye contactoccurs, flood with water for fifteen (15) minutes and call
a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE
INTERNALLY.
