2650 Warfield Street, Fort Worth, TX 76106

Flame Safe FIRE RETARDANT Coatings / Flame Retardant Coatings Hotline: 800-333-9197 8am-5pm (CST) Ph: 817-740-9197 After Hours: 817-658-9197 email: fireprod@aol.com

HOME | CONTACTS | PRODUCTS | MSDS| TESTING

FIRE POLY FPCC

FIRE RETARDANT COATING
for
COMPOSITES ● FIBERGLASS ● PLASTIC ● PLASTIC PIPE ● PVC ● PLASTIC PANELS and SHEATHING ● STYROFOAM ● POLYURETHANE FOAM ●POLYSTYRENE ● FOAM INSULATION ●POLYPROPYLENE ● EPS ● XPS ● HDPE ● POLYISOCYANURATE RIGIFD INSULATION BOARD

NOTATION: It is the intumecence char created when FIRE POLY FPCC coating is exposed to flame or high heat that protects the substrate.

CLASSIFICATION FOR PLASTIC PIPE
INTERNATIONAL MARITIME ORGANIZATION
(MQ) RESOLUTION A 753 (18) ASTM F1173-95
FIRE RETARDANT COATING

TESTING AGENCY
SOUTHWEST RESEARCH INSTITUTE

TEST	MATERIAL TESTED	RESULTS
Fire Endurance and Hydrostatic Evaluation Based on International Maritime Organization Resolution (MQ) Resolution A.753(18); Appendix 2 and ASTM F1173-95 Section A5 Wet Condition Classification of Water Filled Plastic Pipe	Conley epoxy 20, 6-in. FLGXFLG Spool pipe coated with Flame Safe Chemical Corporation's Fire Poly FPCC	Passed

FIRE ENDURANCE	PASSED
Number of fire retardant coats	3
Rate per coat (ft2/gal)	1050

 

FIRE RETARDANT COATING for STYROFOAM ●POLYURETHANE FOAM ● POLYSTYRENE

TEST	MATERIAL TESTED	RESULTS
NFPA 701	3/4" Styrofoam painted with green latex paint and coated with Flame Safe's Fire Poly FPCC 3/4" Styrofoam (white) coated with Flame Safe's Fire Poly FPCC	Passed   Passed

FIRE POLY FPCC	TECHNICAL DATA (Fire retardant Coating for Plastic Pipe, styrofoam)

PRODUCT DESCRIPTION:    Aqueous Based Resin

PRODUCT ANALYSIS
Total Solids	46%		PH	2.5 - 2.8
Weight per gallon	12.4 lbs		Flash point	Non-Flammable
Specific gravity	1.33		Color	Water clear at 78°F. - Slight haze at 50°F. or lower
Volatability	Non-Volatile		Solvents	Water(Contains no petroleum or derivatives of petroleum)
Anti-Fungus	excellent Resistance		Bacterial	Good Resistance
Linear shrinkage	None		Moisture Absorption	Slight
Corrosive	Mildly		Toxic	None (when dry)
Scrubability	1000 cycles		Incompatiblilty	Strong oxidizers, alkalis or acids (materials to avoid)
Toxic	None, when dry

RECOMMENDED USE: Pressurized plastic, composite piping systems, styrofoam, polyurethane foam, styrene

FLAME SAFE FIRE POLY FPCC Specially formulated for use on plastic pipe

ENVIRONMENTAL REGULATION:

This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.

 

	QUICK REFERENCE FOR APPLYING FIRE POLY FPCC

MATERIAL	APPLICATION	COVERAGE
Plastic Pipe, PVC pipe, Composite pipe     Styrofoam, Polyurethane foam, polystyrene, EPS, XPS, HDPE, PC, PVC, PMMC, and other plastic substrates	Be sure surface is clean and dry before treating. Apply with sprayer head held at 8 to 12 inches from surface. Be sure to allow drying between each coat.	Apply three (3) coats at 1050 sq. ft. per gallon with the final coverage rate of 350 sq. ft. per gallon   Apply three (3) coats at 600 sq. ft. per gallon with the final coverage rate of 200 sq. ft. per gallon

EXTERIOR / INTERIOR           All surfaces to be treated must be clean and dry. Fire Poly FPCC is water based, clear liquid that becomes insoluble when dry. If over-coating is intended, Fire Poly FPCC is an excellent primer for use under or over latex paints. DO NOT DILUTE OR MIX FIRE POLY 100 WITH ANY OTHER PRODUCTS. Avoid wasteful runs and dripping. It should be noted that unlike some products, materials treated with Fire Poly FPCC require no special cutting tools or special fasteners. Contact parts of any equipment should be stainless steel or plastic to prevent chemical reaction and breakdown. Storage may be done in polyethylene containers.

Internal fire endurance test for discontinuous filament wound fiberglass Tecnoplast testing

Fire Retardant for Fiberglass (FRP) plastic test Southwest Research Institute

 

CAUTION:

          Product must not freeze. It must not be thinned or diluted.

OVERSPRAY:

        The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with   bleach and water mix will clean up spotting.

CLEAN UP PROCEDURE:

          Airless Equipment.

1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.

2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.

            3. Repeat Step 1 if any foaming occurs in Step 2.

            4. Lubricate system as specified by equipment manufacturer to combat rusting.

If two or more applications are planned in the same day, the sprayer can be kept clean by running water through the system between applications.

          Brushes/Rollers.

              1. Clean immediately after use.

              2. Wash thoroughly with bleach and water mix (1 part to 4 parts).

SAFETY FIRST

Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.

It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.

If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.

HOME | CONTACTS | PRODUCTS

 

The information contained herein is the property of Flame Safe Chemical Corporation and Flame Safe Wood Products, Inc. ©1990 revised 8/20/2009