2650 Warfield Street Ft Worth, TX 76106 |
Flame Safe FIRE RETARDANT Coatings / Flame RetardantsHotline: 800-333-9197 8am-5pm (CST) Ph: 817-740-9197 After Hours: 817-658-9197 email: fireprod@aol.com |
 Fire Retardant for Wood Decking |
Dallas, Fort Worth, Houston, Austin,South Dallas, North Dallas, Dallas County, Houston, Corpus Christi, San Antonio, DFW metroplex, Dallas - Fort Worth, Abilene, Amarillo, Odessa, Midland, El Paso |
FIRE POLY 75 E
EXTERIOR FIRE RETARDANT
COATING or SPRAY
FOR ALL SPECIES EXTERIOR WOOD
PLYWOOD ● LUMBER ● TIMBER
Flame Safe Fire Poly® FP75E is an exterior intumescent fire retardant coating ASTM E84, ASTM D2898; CLASS A; UL723, TYPEI; NFPA255; UBC 8-1 |
CLASSIFIED
FIRE RETARDANT COATING
SURFACE BURNING CHARACTERISTICS OF APPLIED COATING
| Surface | Douglas fir |
| Flame spread | 5 |
| Smoke developed | 115 |
| One coat @ (ft2/gal) | 166 - 200 |
| Number of fire retardant coats | 3 |
| Rate per coat (ft2/gal) | 600 |
| Number of overcoats | None |
FIRE POLY FP75E |
TECHNICAL DATA INTERIOR / EXTERIOR CLASS A RATING |
|---|
PRODUCT DESCRIPTION: Aqueous Based Resin
| PRODUCT ANALYSIS | ||||
|---|---|---|---|---|
Total Solids |
528 | PH | 2.2 - 2.5 |
|
Weight per gallon |
11.5 lbs | Flash point | Non-Flammable |
|
Specific gravity |
1.33 | Color | Water clear at 78°F. - Slight haze at 50°F. or lower |
|
Volatability |
Non-Volatile | Solvents | Water(Contains no petroleum or derivatives of petroleum) |
|
Anti-Fungus |
excellent Resistance | Bacterial | Good Resistance |
|
Linear shrinkage |
None | Moisture Absorption | None |
|
Corrosive |
Mildly | Toxic | None (when dry) |
|
Insects, rodents, aspergilli And other types of molds |
Excellent resistance | Termites | Excellent resistance |
|
Preservative for wood |
Good | Scrubability | 1000 cycles |
|
RECOMMENDED USE: Interior/Exterior Class A Rating (Flame spread less than 25)
FLAME SAFE FIRE POLY75E is a fire retardant coating. It can be used on any type of wood, porous, or non-porous materials, such as:
| Yellow pine | Redwood | Cedar | Douglas Fir |
| Ponderosa Pine | Walnut | Poplar | Reclaimed wood |
| Cyprus | Plywood | Teak | Barnwood |
| Mahoghany | Hardwoods | Softwoods | Wood Decks |
ENVIRONMENTAL REGULATION:
This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.
QUICK REFERENCE FOR APPLYING FIRE POLY FP 75E
MATERIAL |
APPLICATION |
COVERAGE |
| Exterior/Interior wood any type of wood |
Treat before, during or after construction. Apply with sprayer head held at 8 to 12 inches from surface |
Apply one (1) coat at the rate of 166 to 200 sq.ft. per gallon depending on substrate Apply three (3) coats at 600 sq. ft. per gallon with the final coverage rate of 200 sq. ft. per gallon |
EXTERIOR / INTERIOR WOODS All surfaces to be treated must be clean
and dry. Fire Poly 75 E fire retardant coating is water-based, clear liquid that
becomes insoluble when dry.
Fire Poly 75 E
also acts as a preservative, and water proofing agent ultra violet inhibibor, mold and mildew protector and repels insects.. If over coating is intended, Fire
Poly 75 E is an excellent surface primer for use under
latex paints or can be use as a finished coat overwater based stains. It should be noted that unlike some
products, materials treated with Fire Poly 75 E fire retarant coating
require no special cutting tools or special
fasteners. Contact parts of any equipment
should be stainless steel or plastic to prevent
chemical reaction and breakdown. Storage
may be done in polyethylene containers. |
Fire Retardant for Wood - Test Flame Retardant for Wood - Test
|
|---|
CAUTION:
Product must not freeze. It must not be thinned or diluted
OVERSPRAY:
The overspray will not harm plants or animals. Spills can be flushed with water.
A rag wetted with bleach and water mix will clean up spotting.
CLEAN UP PROCEDURE:
Airless Equipment.
1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.
2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.
3. Repeat Step 1 if any foaming occurs in Step 2.
4. Lubricate system as specified by equipment manufacturer to combat rusting.
If two or more applications are planned in the same day, the sprayer can be kept
clean by running water through the system between applications.
Brushes/Rollers.
1. Clean immediately after use.
2. Wash thoroughly with bleach and water mix (1 part to 4 parts).
SAFETY FIRST
Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.
It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.
If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.
Fire Retardant for Marine |
Flame Retardant for Historical Restorartion |
|---|
| Call for pricing and ordering 1-800-333-9197 |
HOME | CONTACTS | PRODUCTS | Fire Poly FP75E MSDS | TESTING