fire retardant logo

2650 Warfield Street Fort Worth, TX 76106 USA

Flame Safe FIRE RETARDANT Coatings / Flame Retardants

Hotline: 800-333-9197 8am-5pm (CST) Ph: 817-740-9197

After Hours: 817-658-9197 email: fireprod@aol.com

  
Dallas, Fort Worth, Houston, Austin,South Dallas, North Dallas, Dallas County, Houston, Corpus Christi, San Antonio, Dallas - Fort Worth, Abilene, Amarillo, Odessa, Midland, El Paso
HOME CONTACT US PRODUCTS Fire Poly FP50 MSDS TESTING
Fire Retardant Coatings - Flame Retardant Coatings - Fire Retardant Sprays
Fire retardant logo Flame Safe

FIRE POLY FP50CC

INTERIOR FIRE RETARDANT COATING or SPRAY FOR ARTIFICIAL PLANTS, FOLIAGE and ARTIFICIAL CHRISTMAS TREES

  FIRE RETARDANT COATING
SURFACE BURNING CHARACTERISTICS OF APPLIED COATING

Flame spread 0.0 - 5
Smoke developed 190
Number of preliminary coats None
Rate per coat (ft2/gal) 200
Number of fire retardant coats 1
Number of overcoats None
Flash point of liquid coating:  
   Fire retarding coating - closed cup, no flash

 

fire retardant logo

FIRE POLY FP50CC

TECHNICAL DATA

INTERIOR FIRE RETARDANT COATING CLASS A RATING

PRODUCT DESCRIPTION:    Aqueous Based Resin

PRODUCT ANALYSIS
Total Solids
 42 - 46   PH
2.6 - 3.2
Weight per gallon
 10.5 - 10.8 lbs Flash point
Non-Flammable
Specific gravity
 1.3 Color
Milky color dries clear
Volatability
 Non-Volatile Solvents
Water(Contains no petroleum or derivatives of petroleum)
Anti-Fungus
 Good Resistance Bacterial
Good Resistance
Linear shrinkage
 None Moisture Absorption
None
Corrosive
 Mildly Toxic
None (when dry)

RECOMMENDED USE: Interior Class A Rating (Flame spread less than 25)

FLAME SAFE FIRE POLY FP50CC is a fire retardant coating. It can be used on:

Plastic Plants Artificial Foliage
Artificial Plants Artificial Christmas Trees

ENVIRONMENTAL REGULATION:

This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.


QUICK REFERENCE FOR APPLYING FIRE POLY FP50CC

MATERIAL
APPLICATION
COVERAGE

Interior Artificial plants, AChristmas Trees,

Treat before, during or after construction.

Be sure surface is clean and dry before treating.

Apply with 80 psi or greater sprayer. Apply fire retardant 8 to 12 inches from surface.

Apply with brush or dipping.

Treat all surface areas where possible.

Do not expose treated area to moisture for 24 hours.

 Apply one coat at 200 sq. ft. per gallon

INTERIOR

           All surfaces to be treated must be clean and dry. Fire Poly FP50CC fire retardant coating is water-based, milky colored liquid, dries clear and becomes insoluble when dry.

DO NOT DILUTE OR MIX FIRE POLY FP50CC fire retardant coating WITH ANY OTHER PRODUCTS.

   Avoid wasteful runs and dripping.  It should be noted that unlike some products, materials treated with Fire Poly FP50CC fire retardant coating require no special cutting tools or special fasteners. Contact parts of any equipment should be stainless steel or plastic to prevent chemical reaction and breakdown. Storage may be done in polyethylene containers.

     Structures can be made fire resistant. Use on substrates athat are enclosed and/or in areas that are warm and dry. Fire Poly FP50CC fire retardant coating creates a varnish like coating that provides a long term fire retardant protection.

Fire retardant for Artificial plants 

Fire retardant coating for artificial plants, artificail foliage, artificial Christmas Trees

CAUTION:

          Product must not freeze. It must not be thinned or diluted.

OVERSPRAY:

        The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with   bleach and water mix will clean up spotting.


CLEAN UP PROCEDURE:

          Airless Equipment.

1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.

2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.

            3. Repeat Step 1 if any foaming occurs in Step 2.

            4. Lubricate system as specified by equipment manufacturer to combat rusting.

If two or more applications are planned in the same day, the sprayer can be kept clean by running water through the system between applications.


          Brushes/Rollers.

              1. Clean immediately after use.

              2. Wash thoroughly with bleach and water mix (1 part to 4 parts).


SAFETY FIRST

Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.

It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.

If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.

Call for pricing and ordering 1-800-333-9197

HOME | CONTACTS | PRODUCTS | Fire Poly FP50 MSDS | TESTING